The DJI Air 3 is at the moment lower than a 12 months outdated with many new to flying drones, lovers, content material creators, and veterans having fun with usually flying and producing content material with it.

Nonetheless, regardless that comparatively younger, the Air 3 would possibly encounter a hiccup or two or could also be gifted or bought to another person this season.

With this in thoughts, can the Air 3 and its accompanying distant controllers be manufacturing unit reset?

Sadly, the DJI Air 3 can’t be manufacturing unit reset. Nonetheless, I’ll talk about rolling again the Air 3 and DJI RC 2’s firmware, when out there, with the DJI Assistant 2 software program. Moreover, I’ll go over the steps wanted to arrange the Air 3 for gifting or promoting: which incorporates unbinding units and deleting profiles.

Allow us to take a deeper have a look at these steps.

DJI Assistant 2 (Client Drone Sequence)

The DJI Assistant 2 (Client Drone Sequence) software program was created by DJI to be used with a lot of its shopper drones to carry out varied duties.

The duty we’re involved with for this text can be rolling again firmware updates, if and when out there.

For earlier fashions of DJI drones utilizing the Assistant 2 software program, there have been certainly choices for bringing a drone again to beforehand launched firmware variations.

As of this text’s writing, there have been no earlier Air 3 firmware variations which might be out there to roll again to. Nonetheless, within the close to future, when and if this selection turns into out there, the steps are coated right here.

» MORE: Does DJI Assistant Work with Air 3 (Answered – With Video)

Downloading & Putting in DJI Assistant 2

To obtain the DJI Assistant 2 software program for the Air 3, choose one of many two following hyperlinks in your pc kind:

After you might have downloaded the software program, set up it utilizing the strategies of set up in your pc kind.

» MORE: DJI Assistant 2: A Full Information (Step-by-Step)

Air 3 Firmware Downgrade (If Accessible)

To attach the Air 3 to your PC or Mac for firmware downgrading, you have to the USB to USB-C cable that got here included with the Air 3.

As a aspect notice, the DJI-included USB-C cable each expenses the Air 3 and acts as an information cable. The information side of the cable is what connects the Air 3 to the DJI Assistant 2 software program.

Not all third celebration USB-C cables are knowledge cables. So, it’s good to see that DJI has included this explicit cable with all their Air 3 combos and packages.

To attach the Air 3:

Step 1: Insert the Air 3’s USB to USB-C cable into an empty USB slot in your pc.

Step 2: Whereas the Air 3 is off, plug the USB-C finish into the Air 3.

Step 3: With the Air 3 plugged into an empty USB slot in your PC or Mac, launch the DJI Assistant 2 software program.

Step 4: For first-time utilization of the DJI Assitant 2 Software program, you have to to be logged into your DJI account, which will be performed within the right-hand nook of the Assistant 2 display screen.

Step 5: After logging into your DJI account or confirming it’s logged in, unfold the Air 3’s legs and arms.

Take away the gimbal cowl and activate the Air 3 by urgent the ability button as soon as after which holding the ability button.

Step 6: The DJI Assistant 2 software program will then launch a display screen that shows an icon representing the Air 3. Select the Air 3.

Step 7: On the left aspect of the display screen select Firmware Replace. You’ll see an inventory of Firmware Variations. If there can be found Firmware variations to downgrade to, you will note this below the Motion area to the correct.

» MORE: How one can Use DJI Assistant 2 with DJI Mini 3 / Mini 3 Professional (Step-by-Step Information)

Distant Controller Firmware Downgrade (If Accessible)

In case you are trying to make use of the DJI Assistant 2 software program along with your DJI RC 2 or RC-N2:

Step 1: Insert the Air 3’s USB to USB-C cable into an empty USB slot in your pc.

Step 2: Whereas the RC 2 or RC-N2 is off, plug the USB-C finish into both the RC 2 or RC-N2. Activate the distant controller.

Step 3: With the RC 2 or RC-N2 plugged into an empty USB slot in your PC or Mac, launch the DJI Assistant 2 software program.

Step 4: The DJI Assistant 2 software program will then transition to a display screen that exhibits both your RC 2 or RC-N2. Select your distant controller.

Step 5: On the left aspect of the display screen select Firmware Replace. You’ll see an inventory of Firmware Variations. If there can be found Firmware variations to downgrade to, you will note this below the Motion area to the correct.

» MORE: How one can Downgrade Your DJI Firmware Utilizing DJI Assistant 2 (Defined)

DJI RC 2 Manufacturing facility Reset

In contrast to the Air 3 and the RC-N2, the DJI RC 2 can be manufacturing unit reset. As a result of the RC 2 is mainly an Android sensible machine, it’s fairly straightforward to reset the distant controller.

Be aware: Manufacturing facility resetting the DJI RC 2 doesn’t roll again the present firmware. It removes all saved person data and knowledge from the distant controller.

To manufacturing unit reset the DJI RC 2, comply with these steps:

STEP 1: After powering on the RC 2, contact the highest of the display screen and slide down twice. This can carry you to the notifications display screen.

STEP 2: Faucet the settings icon on the highest right-hand nook of the display screen.

This can open the settings display screen.

STEP 3: Faucet the System choice on the backside of the display screen.

STEP 4: Faucet Reset Choices

STEP 5: Press Erase all knowledge (manufacturing unit reset)

STEP 6: You’ll then be introduced with an inventory of what is going to be erased from the distant controller. Select Erase all knowledge.

After these steps have been accomplished, the DJI RC 2 will likely be “again to new situation”, from a software program standpoint.

» MORE: How one can Fly DJI Air 3 Drone (With DJI RC 2)

Planning on Promoting or Gifting your Air 3 and DJI RC 2?

Though the Air 3 is a comparatively new drone, there could also be these wishing to provide/present it to relations, or even perhaps promote their Air 3 on-line.

When doing so, along with wiping the information from the DJI RC 2, the Air 3 and RC 2 ought to likewise be unbound from the DJI account and the DJI Profile faraway from the RC 2 distant controller.

» MORE: What to do Earlier than Promoting Your Drone? Learn This First!

Unbinding Units

To unbind the Air 3 and DJI RC 2:

Step 1: Activate the Air 3 and DJI RC 2. Go to your Profile.

Step 2: Within the DJI Profile, faucet Machine Administration.

Step 3: Select the DJI Air 3 (when you have a number of drones).

Step 4: Choose Take away Machine from Account and the Air 3 and DJI RC 2 will likely be eliminated out of your DJI Account.

» MORE: When Ought to You Improve Your Drone? (Learn This First)

DJI Profiles

The final step of the method can be to take away any traces of your DJI profile from the DJI RC 2.

To take away your present DJI Account data from the DJI RC 2:

STEP 1: Boot up the DJI RC 2. As soon as within the DJI Fly app, go to the Profile icon on the backside of the display screen.

STEP 2: When on the Profile display screen, scroll down on the right-hand aspect till you see the Settings tab. Go into Settings.

STEP 3: Select Log Out on the left aspect of the display screen.

STEP 4: Verify you wish to Log Out of your DJI account. You at the moment are performed.

This can promptly take away your private data and flight knowledge from the DJI RC 2. The knowledge is not going to be deleted out of your precise profile, as this data is linked to the person account and never the Air 3.

» MORE: The place Is the Serial Quantity on DJI Air 3 (Answered)